The M10 GPS uses multi-constellation GNSS powered by u-blox M10 series, a concurrent GNSS receiver which can receive and track multiple GNSS systems. Owing to the multi-band RF front-end architecture all four major GNSS constellations, GPS,Galileo, GLONASS and BeiDou can be received concurrently.
It also comes with the IST8310 compass, tricolored LED indicator, buzzer, and a safety switch. There are 3 different connectors options for different purposes. This module ships with a baud rate of 115200 5Hz.
The high-gain 25 x 25 mm patch antenna provides excellent performance and the omnidirectional antenna radiation pattern increases flexibility for device installation. It features active circuitry for the ceramic patch antenna, rechargeable backup battery for warm starts.
Firmware Support for M10 GPS:
- PX4 1.14, ArduPilot 4.3, INAV 5.0.0, Betaflight 4.3.0 or newer is required.
Features
- Newest Ublox 10th Gen GNSS
- Fast & Accurate Positioning
- High-gain 25*25*4mm antenna
- IST8310 Compass
- Internal Buzzer, Safety switch
- Ultra Bright UI RGB LED
Specification
| |
Holybro M10 GPS |
Holybro M9N GPS |
| GNSS Receiver |
Ublox M10 |
Ublox M9N |
| Number of Concurrent GNSS |
Up to 4 GNSS |
Up to 4 GNSS |
| BeiDou |
BeiDou |
| Galileo |
Galileo |
| GLONASS |
GLONASS |
| GPS |
GPS |
| QZSS |
QZSS |
| Frequency Band |
GPS L1 |
GPS L1 |
| Galileo E1 |
Galileo E1 |
| GLONASS L1 |
GLONASS L1 |
| BeiDou B1 |
BeiDou B1 |
| SBAS L1 |
SBAS L1 |
| QZSS L1 |
QZSS L1 |
| Compass |
IST8310 |
IST8310 |
| Output Protocol |
UBX (U-blox) |
UBX (U-blox) |
| NMEA |
NMEA |
| Accuracy |
2.0m CEP |
1.5m CEP |
| Nav. Update Rate |
Up to 25 Hz (single GNSS), |
Up to 25 Hz (4 concerrent GNSS) |
| Up to 10 Hz (4 concurrent GNSS) |
| GNSS Augmentation System |
EGNOS, GAGAN, MSAS and WAAS |
EGNOS, GAGAN, MSAS and WAAS |
| QZSS: L1S |
QZSS: L1S |
| Default Baud Rate |
115200 |
115200 |
| Input Voltage |
4.7-5.2V |
4.7-5.2V |
| Port Type |
JST-GH-10P |
JST-GH-10P |
| Antenna |
25 x 25 x 4 mm ceramic patch antenna |
25 x 25 x 4 mm ceramic patch antenna |
| Power consumption |
Less than 200mA @ 5V |
Less than 200mA @ 5V |
| Operating Temperature |
-40~80C |
-40~80C |
| Dimension |
φ50 x14.4 mm |
φ50 x14.4 mm |
| Weight |
32g |
32g |
| Cable Length |
26cm (42cm cable purchase separately) |
26cm (42cm cable purchase separately) |
| Other |
Tri-color LED |
Tri-color LED |
| Onboard Buzzer |
Onboard Buzzer |
| Safety Switch |
Safety Switch |
| LNA MAX2659ELT+ RF Amplifier |
LNA MAX2659ELT+ RF Amplifier |
| Rechargeable Farah capacitance |
Rechargeable Farah capacitance |
| Low noise 3.3V regulator |
Low noise 3.3V regulator |
PIN MAP
Note: For Ardupilot User, if you are unable to perform normal compass calibration "compass dance" for any reason, set parameter COMPASS_ORIENT=6 (Yaw270) for proper compass orientation.
Difference between the three cable options
Setup with Pixhawk Cube or compatible autopilot
- Connect to GPS port / Telemetry serial port with 6 pin connector
- Disable all other GPS by setting SERIALX_PROTOCOL TO -1
- For example if connected to pixhawk cube on GPS 2 port, set SERIAL3_PROTOCOL TO -1 to disable GPS on GPS1 port. If you are using port for something else set it to any other value than 5.
Package Includes:
- 1x M10 GPS Module
- 1x Fixed Carbon Fiber GPS mount
