This combo of 10 KgCm Torque motor with Microstepping drive is ideal for small and medium sized CNC machines and robots. When used in CNC machines you can get rapid movement speeds up to 4200 mm/min.
RMCS-1102 is Rhino Motion Controls introductory micro-stepping drive for 1.8deg Bipolar Stepper Motors. It is designed for smooth and quiet operation without compromising on torque and control at higher speeds. It has short-circuit protection for the motor outputs, over-voltage and under-voltage protection and will survive accidental motor disconnects while powered-up.
The RMCS-1102 achieves micro-stepping using a synchronous PWM output drive and high precision current feedback and this is absolutely silent when the motor is stopped or turning slowly. It virtually eliminates stopped-motor heating regardless of power supply voltage.
The RMCS-1102’s closed-loop control gains are calibrated on start-up based on motor characteristics and also adjusted dynamically while the motor is in motion. This control algorithm makes it capable of achieving better torque at higher speeds in comparison to comparable drives in its range.
The PULSE/STEP, DIRECTION inputs are optically isolated. Both inputs work with 2.5V, 3.3V or 5V logic drive signals. The input drive current is 5mA at 2.5V so almost all logic family (74LS, 74HC, etc.) can be used to drive these inputs. Each input provides individual anode and cathode connections to the opto-isolator allowing for multiple input drive interfaces.
Motor Features
- Step Angle : 1.8 Degree
- Configuration: 4 wire stepper motor
- Holding Torque: 10.2kgcm bipolar
- Rated voltage : 3.3VDC
- Phase current : 2Amp
- Resistance/phase: 1.65E
- Inductance/Phase : 2.2mH
- Rotor inertia: 275 gcm2
- Detent torque: 0.36kgcm
- Length (L): 51mm
- Weight: 650 grams
Micro-Stepping Drive Features:
- Smooth and quiet operation at all speeds and extremely low motor heating
- Industrial grade performance for 2-Phase Bipolar Stepper Motors
- Input supply voltage from 12VDc to 50VDC
- Selectable peak coil current from 0.5A to 5.0A
- Inaudible 20kHz current chopping frequency
- Selectable half-current during motor standstill to further reduce motor heating
- Selectable micro-steps up to 8000 steps per rotation for a 1.8deg stepper motor
- Higher motor torque and higher speeds achievable due to advanced loop control algorithm
- 2.5V, 3.3V and 5V compatible PULSE and DIRECTION inputs with 2-wire opto-isolated interface
- Short-circuit protection for the motor outputs, over-voltage and under-voltage protection
- LED indication for power and error states
Power and Motor Terminal Assignments
|
Terminal No.
|
Terminal Name
|
Description
|
|
Terminal 1
|
GND
|
Power Ground or Power –Ve
|
|
Terminal 2
|
+V
|
Power +Ve (18VDC to 50VDC Max wrt. GND)
|
|
Terminal 3
|
B-
|
Motor Coil Phase B-
|
|
Terminal 4
|
B+
|
Motor Coil Phase B+
|
|
Terminal 5
|
A-
|
Motor Coil Phase A-
|
|
Terminal 6
|
A+
|
Motor Coil Phase A+
|
Pulse and Direction Input Assignments
|
Terminal No.
|
Terminal Name
|
Description
|
|
Terminal 1
|
ENA-
|
Enable (Motor Free) -Ve optically isolated input
|
|
Terminal 2
|
ENA+
|
Enable (Motor Free) +Ve optically isolated input
|
|
Terminal 3
|
DIR-
|
Direction -Ve optically isolated input
|
|
Terminal 4
|
DIR+
|
Direction +Ve optically isolated input
|
|
Terminal 5
|
PUL-
|
Pulse -Ve optically isolated input
|
|
Terminal 6
|
PUL+
|
Pulse +Ve optically isolated input
|
Switch Selection Table for Motor Coil Current Setting
|
Peak Current
|
SW6
|
SW7
|
SW8
|
|
0.50A
|
OFF
|
OFF
|
OFF
|
|
1.00A
|
OFF
|
OFF
|
ON
|
|
1.40A
|
OFF
|
ON
|
OFF
|
|
2.00A
|
OFF
|
ON
|
ON
|
|
2.80A
|
ON
|
OFF
|
OFF
|
|
3.30A
|
ON
|
OFF
|
ON
|
|
4.20A
|
ON
|
ON
|
OFF
|
|
5.00A
|
ON
|
ON
|
ON
|
Switch Selection Table for Step Resolution Setting
|
Steps/Rev
|
SW1
|
SW2
|
SW3
|
SW4
|
|
200
|
ON
|
ON
|
ON
|
ON
|
|
400
|
OFF
|
ON
|
ON
|
ON
|
|
800
|
ON
|
OFF
|
ON
|
ON
|
|
1000
|
OFF
|
OFF
|
ON
|
ON
|
|
2000
|
ON
|
ON
|
OFF
|
ON
|
|
3200
|
OFF
|
ON
|
OFF
|
ON
|
|
4000
|
ON
|
OFF
|
OFF
|
ON
|
|
8000
|
OFF
|
OFF
|
OFF
|
ON
|
|
1600
|
ON
|
ON
|
ON
|
OFF
|
|
6400
|
OFF
|
ON
|
ON
|
OFF
|
|
10000
|
ON
|
OFF
|
ON
|
OFF
|
|
12000
|
OFF
|
OFF
|
ON
|
OFF
|
|
12500
|
ON
|
ON
|
OFF
|
OFF
|
|
12800
|
OFF
|
ON
|
OFF
|
OFF
|
|
16000
|
ON
|
OFF
|
OFF
|
OFF
|
|
20000
|
OFF
|
OFF
|
OFF
|
OFF
|
Switch in downward positions is ON
SW5 ON - Half-Current during Stand-still
SW5 OFF - Full-Current during Stand-still
Package Includes:
- 1 x NEMA23 STEPPER MOTOR 10KGCM TORQUE
- 1 x RHINO MICRO-STEPPING STEPPER MOTOR DRIVE 15-42V 5AMP
Downloads
User Manual
Motor Datasheet
